Free Standing Bidet Toilet Factory
Free Standing Bidet Toilet – Factory Overview
The free standing bidet toilet combines a conventional water closet with an integrated bidet function in a single floor‑mounted fixture. It eliminates the need for separate bidet plumbing while maintaining the same footprint as a standard toilet.
Flushing is typically achieved via a siphon jet or washdown system. The bidet nozzle operates from a dedicated water supply line with adjustable pressure and temperature controls.
Water consumption for the flushing cycle averages 4.8 liters per full flush, complying with most regional low‑flow standards. The bidet spray uses approximately 0.6 liters per minute at nominal pressure, allowing precise cleaning with minimal waste.
Key Technical Specifications
| Parameter | Typical Value | Notes |
|---|---|---|
| Flush type | Siphon jet or washdown | Selected per project requirements |
| Flush volume | 4.8 L per full flush | Adjustable via valve setting |
| Bidet nozzle flow rate | 0.6 L/min at 0.2 MPa | Customizable spray patterns |
| Supply pressure range | 0.1–0.5 MPa | Inlet pressure regulator recommended |
| Bowl material | Vitreous china | High‑temperature fired, glazed |
| Seat material | Polypropylene (optional heated) | Glass‑fiber reinforced for durability |
| Overall dimensions (L×W×H) | 700 mm × 380 mm × 780 mm | Customizable within standard rough‑in |
| Weight | ≈35 kg | Depends on options |
| Electrical rating (heated seat) | 45 W, 12 V DC | Low‑voltage, thermostat controlled |
Materials and Construction
The vitreous china bowl is formed using high‑temperature firing to achieve low porosity and resistance to staining. Internal surfaces are glazed to a smooth finish that inhibits bacterial growth and simplifies cleaning.
The bidet nozzle is constructed from stainless steel grade 304, selected for corrosion resistance in constant water exposure. It retracts into a hygienic housing when not in use, preventing contamination from external particles.
Optional heated seats incorporate a low‑voltage carbon fiber heating element rated at 45 W, with temperature regulation via a built‑in thermostat. Lid and seat are made from polypropylene reinforced with glass fiber for impact strength and dimensional stability.
Manufacturing Considerations
Production begins with precision molding of the bowl and tank halves under controlled humidity to avoid defects. After firing, each unit undergoes a dimensional inspection using laser scanning to verify tolerances within ±2 mm. The bidet assembly is then installed, and functional tests confirm spray pattern, pressure, and temperature stability.
Quality Assurance
Quality control follows a multi‑stage protocol that includes visual inspection, leak testing, and performance validation. Leak testing is performed at 1.5 times the rated supply pressure for 30 seconds, with no allowable seepage. Performance validation measures flush effectiveness using standardized waste simulators and bidet spray coverage using dye‑based test cards.
Typical Applications
In high‑traffic commercial restrooms, the integrated bidet reduces the need for separate fixtures, conserving floor space and simplifying plumbing rough‑in. This layout also lowers installation labor because only one waste and water supply connection is required per unit.
Healthcare environments benefit from the hands‑free cleaning action, which can help reduce cross‑contamination compared to traditional toilet paper use. The antimicrobial glaze and easy‑to‑clean surfaces support infection control protocols.
Hospitality venues such as hotels and resorts often select free standing bidet toilets to offer guests a premium amenity without extensive bathroom renovations. The fixture’s standard rough‑in dimensions allow replacement of existing toilets with minimal structural changes.
Customization Options
Customers can specify bowl finishes ranging from standard white to custom colors achieved through pigmented glazes. Seat options include standard polypropylene, heated variants with adjustable temperature, and soft‑close hinges.
The bidet nozzle can be configured for dual‑temperature (hot/cold) or single‑temperature operation, with optional pulsating or aerated spray patterns. Control panels may be mounted on the tank side or integrated into a remote‑access wall plate, depending on user preference and ADA requirements.
Frequently Asked Questions
Can the dimensions be customized?
Yes, the overall length, width, and height can be adjusted within standard rough‑in limits to suit specific installation constraints; detailed drawings are required for quotation.
What information is required before quotation?
To generate a quote we need the intended flush volume, nozzle configuration, seat heating preference, any custom color or branding, and the projected order quantity.
What materials are available for the bowl and seat?
Bowls are supplied in vitreous china; alternative ceramic composites are available upon request. Seats are offered in polypropylene, heated polypropylene, or urea‑formaldehyde for specific durability needs.
How is quality inspected?
Each unit undergoes visual inspection, hydrostatic leak test at 1.5× pressure, functional spray test, and final dimensional audit before packaging.
What packaging methods are available for export shipments?
Standard packaging includes a corrugated carton with internal foam corners and a polyethylene moisture barrier. Palletizing and custom crating can be arranged for long‑distance transport.
What is the typical production lead time?
Lead time ranges from 4 to 6 weeks after receipt of approved drawings and deposit, depending on order size and customization complexity.
Contact Us
To discuss technical details, request a quotation, or arrange a sample, please contact our sales team.
Contact Sales
