Oem Large Wall Mounted Bathroom Cabinet
OEM Large Wall Mounted Bathroom Cabinet
This cabinet is designed for wall‑mounted installation in high‑traffic commercial restrooms where floor space is limited. Typical overall dimensions range from 800 mm to 1200 mm width, 500 mm to 700 mm height, and 180 mm to 250 mm depth, providing ample storage while maintaining a low profile.
Design and Dimensions
The cabinet frame is constructed from 18 mm marine‑grade plywood or 1.2 mm stainless steel sheet, selected based on corrosion resistance requirements. Door panels are fitted with concealed hinges that allow a 110° opening angle, and internal shelving is adjustable in 25 mm increments to accommodate varied toiletries.
Load testing shows the unit safely supports up to 150 kg of evenly distributed weight when fastened to concrete or stud walls with the supplied M8 anchor bolts. Deflection under maximum load remains below 2 mm, ensuring door alignment over the product lifecycle.
Material Construction
Substrate options include:
- Marine‑grade plywood with a phenolic laminate finish, resistant to moisture and cleaning agents.
- Brushed 304 stainless steel with a passivated surface for aggressive chemical environments.
- High‑density polyethylene (HDPE) core with a UV‑stable acrylic coating for lightweight applications.
Surface finishes are available in matte, satin, or gloss levels, measured by a 60‑degree gloss meter ranging from 10 GU (matte) to 80 GU (gloss). Edge sealing is performed with a PVC edge band of 2 mm thickness to prevent water ingress.
Customization Options
Dimensional adjustments are possible in 10 mm increments for width, height, and depth, limited by structural considerations. Door configurations can be specified as single‑leaf, double‑leaf, or sliding panels, each with corresponding hardware selections.
- Internal accessories: adjustable glass shelves, stainless steel towel bars, or integrated LED lighting strips.
- Locking mechanisms: cam locks, electronic keypads, or RFID‑enabled handles.
- Ventilation provisions: perforated rear panels or passive air vents sized to meet local code requirements.
Installation and Mounting
The cabinet is supplied with a pre‑drilled mounting plate that aligns with standard 16‑inch stud spacing or concrete anchors. Installation torque for M8 bolts is recommended at 25 Nm to achieve optimal shear resistance. A leveling shim kit is included to compensate for wall irregularities up to 5 mm.
Electrical provisions for integrated lighting are routed through a concealed conduit with a IP44 rating, ensuring protection against splashing water. All hardware is packaged separately to avoid surface damage during transit.
Typical Applications
In hotel guest bathrooms, the cabinet provides secure storage for guest amenities while maintaining a sleek profile that complements modern interior designs. Hospital installations benefit from the non‑porous surfaces and easy‑clean finishes that support infection control protocols.
Public facilities such as airports and transit stations utilize the unit’s high load capacity and vandal‑resistant hardware options to withstand frequent use and potential misuse. The wall‑mounted configuration frees floor space for wheelchair access and cleaning equipment.
Quality Assurance and Testing
Dimensional verification is performed on a CNC coordinate measuring machine with a tolerance of ±0.5 mm on critical interfaces. Finish adhesion is assessed via cross‑hatch testing according to ASTM D3359, requiring a minimum rating of 4B.
Load testing follows ANSI/BIFMA X5.1 standards for storage units, applying a static load of 150 kg for 24 hours with subsequent inspection for permanent deformation. Corrosion resistance of stainless steel variants is validated using salt‑spray exposure (ASTM B117) for 500 hours with no red rust observed.
Typical Specifications
| Parameter | Typical Value | Notes |
|---|---|---|
| Width | 800 mm – 1200 mm | Customizable in 10 mm steps |
| Height | 500 mm – 700 mm | Customizable in 10 mm steps |
| Depth | 180 mm – 250 mm | Customizable in 10 mm steps |
| Maximum Load | 150 kg | Evenly distributed, wall‑mounted |
| Material Thickness | 18 mm (plywood) / 1.2 mm (SS) | Substrate dependent |
| Finish Gloss | 10 GU – 80 GU | Matte to gloss options |
Frequently Asked Questions
- Can dimensions be customized? Yes, width, height, and depth can be adjusted in 10 mm increments based on project requirements.
- What information is required before quotation? Desired overall dimensions, substrate preference, finish grade, hardware selections, and quantity.
- What materials are available? Marine‑grade plywood with phenolic laminate, brushed 304 stainless steel, and HDPE core with acrylic coating.
- How is quality inspected? Dimensional checks via CMM, finish adhesion per ASTM D3359, load testing per ANSI/BIFMA X5.1, and corrosion resistance via salt‑spray (ASTM B117).
- What packaging methods are available? Individual units are wrapped in polyethylene foam, placed in corrugated cartons with corner protectors, and palletized for export.
- How are export shipments protected? Pallets are stretch‑wrapped and secured with steel straps; moisture‑barrier liners are included for ocean freight.
- What is the typical production lead time? Lead time ranges from 4 to 6 weeks after final drawing approval, depending on material availability and order size.
- How are samples arranged? Sample units can be produced upon request; shipping costs are borne by the requester.
Contact for OEM Inquiry
To discuss custom specifications, request a quotation, or obtain technical drawings, please reach out using the link below.
Submit Inquiry
