Freestanding White Gloss Bathroom Cabinets

This section describes the core construction, dimensional parameters, surface finish, and installation considerations for freestanding bathroom cabinets featuring a white gloss finish.

Material Composition

Cabinets are constructed from medium-density fiberboard (MDF) with a nominal thickness of 18 mm ±0.5 mm, providing a balanced stiffness-to-weight ratio suitable for vertical load bearing. The core is bonded with a urea‑formaldehyde resin that meets low formaldehyde emission class E1. Edge sealing employs a 0.5 mm PVC band to limit moisture ingress at cut faces.

• MDF core density: 680‑720 kg/m³ (typical)
• Formaldehyde emission: ≤0.1 ppm (E1)
• Edge seal material: PVC, thickness 0.5 mm, width 12 mm

Dimensional Specifications

Standard units are offered in three height modules: 800 mm, 900 mm, and 1000 mm, each with a width of 600 mm and depth of 350 mm. Tolerances on overall dimensions are ±2 mm for height and width, ±1 mm for depth, allowing seamless alignment with adjacent fixtures.

Internal shelving consists of two adjustable shelves spaced at 250 mm intervals, each shelf thickness 16 mm and load capacity rated at 20 kg uniformly distributed.

Surface Finish Characteristics

The visible faces receive a multi‑layer UV‑cured acrylic coating. The base layer is a white pigmented primer (TiO₂ content ≈20 wt %), followed by a clear gloss topcoat. Measured gloss at 60° incidence typically ranges from 80 to 90 Gloss Units (GU) according to ISO 2813, providing a reflective surface that enhances perceived brightness in wet environments.

Coating thickness averages 40 µm (±5 µm), delivering a pencil hardness of 2H and resistance to common household chemicals such as sodium hypochlorite (5 % solution) for up to 24 hours without visible degradation.

Structural Design & Mounting

The cabinet employs a full‑depth back panel of 6 mm HDF, affixed with 4 mm staples and reinforced with corner brackets of galvanized steel (thickness 1.2 mm). This configuration increases racking resistance to approximately 150 Nm before observable deformation.

Leveling feet are adjustable from 0 to 15 mm via threaded stainless‑steel inserts, allowing compensation for uneven floor surfaces while maintaining a maximum static load of 120 kg on the cabinet base.

Applications in Commercial Environments

Freestanding white gloss cabinets are commonly specified in hotel guest bathrooms, healthcare facility washrooms, and high‑end residential projects where a seamless, reflective surface aids in light distribution and simplifies cleaning routines. The absence of wall‑mounted hardware reduces installation time and eliminates the need for structural wall reinforcement.

In environments with frequent moisture exposure, the PVC edge seal and low‑emission MDF core limit swelling, contributing to a service life expectancy of 10‑15 years under typical maintenance intervals.

Quality Assurance & Testing

Each production lot undergoes dimensional verification using a coordinate measuring machine (CMM) with a repeatability of ±0.02 mm. Gloss uniformity is assessed across five points per panel; acceptable variation is ≤5 GU. Additionally, a 24‑hour condensation test (40 °C, 95 % RH) checks for delamination or blistering of the coating.

• Dimensional tolerance verification: CMM, ±0.02 mm
• Gloss uniformity: ≤5 GU variation across panel
• Condensation resistance: 40 °C/95 % RH, 24 h, no visual defects

Customization Options

While the standard offering is a white gloss finish, alternative pigmentations (e.g., ivory, light gray) can be matched to RAL or NCS specifications upon request. Shelf configuration may be altered to include a fixed middle shelf or a pull‑out tray, with corresponding adjustments to load ratings. Handle options range from concealed finger pulls to stainless‑steel bar handles (diameter 16 mm, length 150 mm).

Specification Table

Parameter	Typical Value	Notes
Core Material	MDF (E1)	Thickness 18 mm ±0.5 mm
Panel Dimensions (H×W×D)	800/900/1000 mm × 600 mm × 350 mm	Tolerance ±2 mm (H,W), ±1 mm (D)
Gloss Level (60°)	80‑90 GU	ISO 2813
Coating Thickness	40 µm ±5 µm	UV‑cured acrylic
Load Capacity (Shelf)	20 kg UDL	Per shelf
Adjustable Foot Range	0‑15 mm	Stainless‑steel insert

Inquiry & Technical Support

For project‑specific quotations, lead‑time estimates, or to request a sample panel, please contact our technical sales team. Provide the required dimensions, finish preferences, and any accessory specifications to receive a detailed response.

Request Quote / Sample